Wi-Fi Dimmer 3x 250W, Lighting control with iOS and Android Smartphone/Tablet

_

AQStation DIM 3x 250W

Order-Nr.: 90.10.100

Type: AQS DIM 3X 250W

The AQStation DIM 3x 250W is a 3 channel Wi-Fi Trailing Edge Dimmer (phase-interval). They are suitable for the dimming control of incandescent lamps, low-voltage halogen lamps via electronic transformers, high-voltage halogen lamps as well as Power-LEDs and LED converter. DIN rail mount.

   

 

Network connected via ethernet cableNetwork connected via Wi-Fi3 channelDimmer outputphase-cut load dimmerlight bulbfluorescent bulbLED light

Function
The AQStation Dim 3 x 250 W LAN/Wi-Fi-controlled load dimmer for three circuits. Each circuit has a 250W/VA phase-cut load dimmer intended for the dimming of high-voltage halogen lamps, low-voltage halogen lamps (via electronic transformers), power-LEDs (230 V), LED converters and incandescent light bulbs. The three circuits are independently controllable. The in-house LAN/Wi-Fi is used as a bus system. This enables the use of off-the-shelf smartphones and tablet computers running on Android or iOS to control and visualise AQStation devices. The AQStation Dim 3x 250W can be controlled with its integrated push-button panel, peripheral push-button panels or the relevant AQStation App. For more information about the visualisation, scenes, groups and timer functions, see the AQStation App description available from www.altenburger.de or www.aqstation.de.

Dimming, turning on/off
In the "OFF" mode, the dimmer adjusts the connected load down to almost 0. The load is not disconnected from the network (disengaged function/no galvanic isolation). A command made with a push-button triggers the programmed switch-on value. A command made through the App icon causes the value to rise from 0% to 100%. Using the App, you can set the initial value (between 0 and 100%) of the dimmer in the case of a blackout. The factory-set initial value is 0%. Using the App and the control push-buttons, you can adjust the dimmers between 0 and 100%. The control keys have the following functions: On/Off/Brighter/Darker.

Connectible loads
Using the dimmer, you can control loads (ohmic loads, e.g. incandescent light bulbs) and capacitive loads (e.g. electronic transformers) within a range of 15W/VA to 250W/VA. The total capacity of the connected load may not exceed the maximum load of the dimmer. The power dissipation and cos φ of the electronic transformers should be taken into account as well. The dimmer's maximum output current may not be exceeded as well. You may not connect the outputs of multiple dimmers. Electronic transformers may be connected to the dimmers on the mains (primary) side only. Their loads must comply with the manufacturer's data and they must be designed for appropriate mains electricity. Open-loop operation is not allowed. Electronic transformers may be connected only when they are designed for phase-cut operation. The operation of conventional transformers or inductive loads is generally not allowed, as it might damage the dimmer or the transformers beyond repair.

Load output

  • Electronic current limitation (short-circuit current)
  • Downward adjustment when maximum allowed temperature is exceeded
  • Switching off when the temperature is too high (thermal cut-off, permanent)
  • Switching off when the current is too high (microfuse, permanent)
  • Switching off when voltage peaks are too high (inductive load), switching ON again after disconnection of supply voltage

 

Technical Data:

Designation AQStation Dim 3x 250W
Type AQS DIM 3x 250W
Order Number 90.10.100
Supply Voltage 230V~ 50Hz, DC not allowed
Protection external 6A, internal microfuse
Mounting form DIN rail housing
Dimensions, weight WxHxD=175 x 83.5 x 58 mm, approx. 200 gr.
Internal displays

1x green LED (Wi-Fi mode)

3x green LED (switch mode) at control push-buttons

Internal controls

3x push-buttons for the manual control (on/off, brighter/darker)

1x reset push-button (factory settings, including Wi-Fi)

Wi-Fi 2.4 GHz 802.11n
LAN RJ45, 100-MBit-Ethernet (Fast Ethernet)
Operating temperature 0°C … +35°C
Power consumption < 2 W
Protection class II (protective isolation)
Protection category IP 20
Degree of contamination 2 (dry non-conductive)
Dimmer output 250W/VA (max. 1.0A~)
- Electronic current limitation (short-circuit current)
- Downward adjustment when maximum allowed temperature is exceeded
- Switching off when the temperature is too high (thermal cutoff, permanent)
- Switching off when the current is too high (microfuse, permanent)
- Switching off when voltage peaks are too high (inductive load), switching ON again after disconnection of supply voltage
Loading capacity max. 250W/VA (max 1.0 A~) ohmic load, capacitive load(incandescent light bulbs, electronic transformers)
Qualification CE, RoHS, WEEE

 

 

Downloads:

 

Android app on Google Play

 

Apple and Apple logo are trademarks of Apple Inc., registered in the U.S. and other countries. App Store is a service mark of Apple Inc.

Google Play is a trademark of Google Inc.